Email：gwdlcom@gmail.com |
sales@gwdl.com
Telephone/WhatsApp：+86-15637962277
| 類別 / Category | 1100°C系列 / 1100°C Series |
|---|---|
| 參數 / Parameters | |
| 型號 / Model | GWL-1100d |
| 爐膛尺寸mm：長寬高 / Chamber Dimensions mm: LWH | 600*350*300 |
| 電源AC / Power Supply (AC) | 380V |
| 最高使用溫度 / Max. Operating Temperature | 1100°C |
| 可長期使用溫度 / Long-term Operating Temperature | 1050°C |
| 控制范圍 / Control Range | 50至1270°C / 50 to 1270°C |
| 測量元件 / Measuring Element | 熱電偶分度號K，測量范圍0-1320度 / Thermocouple Type K, Measuring Range 0-1320°C |
| 發熱元件安裝位置 / Heating Element Location | 兩側（進口1800型硅鉬棒加熱元件）/ Both sides (Imported 1800-type silicon molybdenum rod heating elements) |
| 控溫精度 / Temperature Control Accuracy | ±1°C（集成化電路控制，無超調現象）/ ±1°C (Integrated circuit control, no overshoot) |
| 爐溫均勻性 / Temperature Uniformity | 溫度均勻性：±5°C（參照GB5425-2012,計量溫度范圍為300-1000°C,溫度點選取 300°C、450°C、650°C、1000°C。5點測溫，空載測量。設備出口前執行帶接線開關后測溫方式計算是否合格，第三方由省方觀察計量，儀器儀表、熱電偶需有計量證書）（參考表格下附件，以往檢測報告）/ Temperature uniformity: ±5°C (According to GB5425-2012, measured temperature range 300-1000°C, measuring points at 300°C, 450°C, 650°C, 1000°C. 5-point measurement, no load. Tested before shipment with connection switch; third-party verification required, instruments and thermocouples need calibration certificates) (Refer to attached documents and previous test reports below the table) |
| 排氣口 / Exhaust Port | 爐膛設置一個排氣口，手動開啟設計，及時排除煙塵與反應廢氣 / The furnace chamber is equipped with one exhaust port, manually operated, for timely discharge of smoke and reaction gases. |
| 耐火材料 / Refractory Material | 爐內使用采用進口德國MESCHUPP真空成型高純氧化鋁纖維輕質板材料，取樣物料承壓板（爐底）采用高純輕質空心氧化鋁板，使用溫度高，蓄熱量小，耐急冷急熱，不裂縫，不粉化，保溫性能好（節能效果是老式電爐的90%以上）/ The furnace uses imported German MESCHUPP vacuum-formed high-purity alumina fiber lightweight board. The material support plate (furnace bottom) uses high-purity lightweight hollow alumina board, featuring high service temperature, low heat storage, resistance to thermal shock, no cracking, no powdering, and good insulation (Energy saving effect is over 90% compared to old furnaces). |
| 保溫材料 / Insulation Material | 采用四層保溫，分別為：氧化鋁纖維毯、氧化鋁纖維板、氧化鋁多晶纖維板，進口材料，節能效果是老式電爐的90%以上。/ Four-layer insulation, consisting of: alumina fiber blanket, alumina fiber board, alumina polycrystalline fiber board. Imported materials. Energy saving effect is over 90% compared to old furnaces. |
| 爐體外殼溫度 / Furnace Shell Temperature | 長期使用不燙手，外殼溫度不大于45度 / Low external temperature during long-term use, shell temperature ≤ 45°C |
| 保護 / Protection | 采用集成化模塊控制單元，控制精度準確，并設計了雙回路控制和雙回路保護，具備了過沖、超調、欠調、斷偶、缺相、超壓、超流、超溫、電流反饋、軟啟動等保護 / Integrated modular control unit ensures accurate control. Features dual-loop control and dual-loop protection, including overshoot, over-adjustment, under-adjustment, thermocouple break, phase loss, over-voltage, over-current, over-temperature, current feedback, soft start protections, etc. |
| 控制 / Control | 采用閉環技術可控硅模塊觸發控制，移相模塊控制使輸出電壓、電流或功率平滑跟隨設定曲線，具有恒電壓、恒電流或恒功率的特性；電流為內環，電壓為外環，當負載電壓或負載電流超過額定值時，限制調整管的輸出電流在額定電流范圍內，確保發熱元件正常工作；同時電壓參與調節，使調壓器的輸出電流被限制在額定電流范圍內，在有充分調節余量的前提下維持輸出電流及電壓的恒定；從而保護爐內發熱元件免受過大電流、電壓的沖擊，達到安全可靠的控制效果及控制精度。詳見電爐手冊。/ Uses closed-loop technology with thyristor module phase-shift trigger control. This control method allows the output voltage/current or power to smoothly follow the set curve. It has constant voltage, constant current, or constant power characteristics. Current serves as the inner loop, voltage as the outer loop. When the load voltage or current exceeds the rated value, it limits the output current to within the rated range, ensuring normal operation of the heating elements. Simultaneously, voltage participates in regulation, limiting the output current of the voltage regulator within the rated range, maintaining constant output current and voltage when sufficient regulation margin exists. This protects heating elements from excessive current/voltage impact, achieving safe, reliable control and high accuracy. See furnace manual for details. |
| 顯示參數 / Display Parameters | 溫度、溫度段號、段時間、剩余時間、輸出功率百分比、電壓、電流等 / Temperature, temperature segment number, segment time, remaining time, output power percentage, voltage, current, etc. |
| 按鈕 / Buttons | 采用進口按鈕使用壽命超過100000次，并且帶有指示燈。/ Imported buttons with lifespan over 100,000 cycles, with indicator lights. |
| 溫度曲線設定 / Temperature Curve Setting | 采用智能溫度控制儀，備標準PID、人工智能調節AI-PID或MPT等多種調節方式，具有自整定、自學習功能，無超調及無欠調的優良控制特性，具備30段程序控制功能，可實現任意斜率的升、降溫控制，具有跳轉（循環）、運行、暫停及停止等可編程/可操作命令，并允許在程序的控制運行中隨時修改程序；采用具備曲線擬合功能的人工智能調節算法，能獲得光滑平滑的曲線控制效果；詳見電爐手冊。/ Uses intelligent temperature controller with standard PID, artificial intelligence AI-PID, or MPT and other modes. Features self-tuning, self-learning function, excellent control characteristics with no overshoot/undershoot. 30-segment program control function allows arbitrary slope heating/cooling control. Includes programmable/operational commands like jump (loop), run, pause, stop. Allows program modification during operation. Uses AI algorithm with curve fitting function for smooth curve control effect. See furnace manual for details. |
| 多條曲線輸入 / Multi-curve Input | 30段（可定制50段）程序控制功能，可以輸入設定：一條曲線為30(50)段，兩條曲線14(28)段/條，三條曲線10(15)段/條，五條曲線6(9)段/條；可同時輸入多條曲線，用戶可任意調用。/ 30-segment (customizable to 50 segments) program control function. Setting examples: one curve with 30(50) segments; two curves with 14(28) segments each; three curves with 10(15) segments each; five curves with 6(9) segments each. Multiple curves can be input simultaneously and called arbitrarily by the user. |
